Electrical update, what to do?

Power from the electrical company's line flows through a home's outside meter and into the electrical service panel, which controls the flow of electricity into the house. Total electrical usage cannot exceed the panel's capacity. Electrical panels in an older home might have a low capacity as low as 60-100 amp- and some even using an old fuse box which is considered as a serious sub-standard condition- but many new homes are being built at 200 amps.

This is not a do-it-yourself project; Panel and wiring changes should be done by a licensed electrical contractor which is also insured and bonded, he will contact your city planning department for any local restrictions or requirements; a permit is needed and the costs vary widely nationwide for the upgrading process. Many older houses do not have sufficient electrical outlets that are adequate for all the electrical needs. If this is the case for you, you should contact a licensed electrician to come out to your house to give you an estimate of what it will cost to install more electrical outlets, you might want to consider upgrading the old wiring and bringing it up to the latest code requirements. Other electrical problems like power surges or circuit breaker or fuse problems are also things that a licensed electrician can help with. Electrical problems are potentially dangerous, so this is one of the critical reasons why you should always have a professionally trained electrician do all of your electrical work. Many electrical fires happen because property owners fail to take electrical problems seriously. Many fires could be avoided if they are addressed in a timely manner and handled by a professional licensed electrician. Power outages and fires can not only be dangerous but costly too, especially for a business. If you have any dimming or flickering light, old wiring or visibly frayed wires you should call a licensed electrician to come out to assess your situation.

The question now is how to select a reliable dependable licensed electrician?

Selecting the right electrical contractor isn't as easy as picking someone out of the Yellow Pages. The ramifications of hiring the wrong contractor can be financially disastrous and even dangerous. First and foremost, it's imperative to know if the contractor you're considering hiring, is licensed, bonded, and has adequate general liability and workers compensation insurance. Then, you need to determine if they are experienced in the type of work you need performed, and if they are generally considered good, honest and reputable.

Most people think that they should get multiple bids for every job. This isn't the case, and in actuality, putting to bid every little job may in fact backfire.

Good contractors are few and far in between, and asking for multiple bids for a job will only alienate them the next time around. But how can you tell if the first contractor walking into your house is The good contractor? Some simple rules may apply here, but remember there also are exceptions to every rule.

* A good licensed contractor will typically look the part. In other words, if he or she looks messy and disorganized, then it's probably indicative of the type of work he or she does. Someone who takes pride in their work usually takes pride in their appearance. Some contractors may argue this point, but remember we're talking generalities here and not the exceptions. He or she should have some type of company identification as a company cards with their company name and / or their name, telephone and license # on it.

* A good licensed contractor will respond to your calls quickly and provide you with a free estimate the same day or within a reasonable amount of time, and will take the time to explain what they will do and how they will do it.

* A good licensed contractor will never offer to do the job without taking out permits and may even walk away from a job if the homeowner insists on not taking them. Remember, permits are additional insurance for the homeowner guaranteeing (through inspection) that the job was performed safely and correctly.

* A good licensed contractor will never cut corners and do something unsafe in order to accommodate your budget. They will, instead, offer suggestions on how to modify your plans to meet both their code and safety requirements, and your budget. If these two cannot meet, then they will wish you good luck and walk away from the job: Suppose a homeowner would like to make a minor alteration or addition to their electrical system. If the electrical system is old, then that part of the system may need to be brought up to current code standards before they can add to it or modify it. In order to circumvent this regulation, the homeowner may insist that the job be done without permits. A good contractor wouldn’t do it and the homeowner may end up hiring an unlicensed contractor. What he or she doesn't realize is that if their house burns down, they will very likely NOT be covered. Your homeowner's policy probably states (very clearly) that anyone doing work on the residence has to be properly licensed and all building, plumbing and electrical codes must be followed, and work performed with permits wherever required. If you hired someone whom you thought was licensed, but ultimately wasn't, it still may NOT be covered because you didn't take out permits for the work, and as far as the insurance company is concerned, it was done illegally.

* A good licensed contractor will be happy to provide you with copies of their insurance certificates and references when asked. If and when you decide to put a job out to bid, make sure that the work is properly specified (in minute detail) so that all the contractors are bidding on exactly the same things. Otherwise, there's no way of telling who's bidding apples and who is bidding oranges. Not properly specifying a job is probably the most common mistake homeowners make. Why? Let's assume you need to have 10 receptacles, 4 lights and 2 dimmers installed in a room. Without specifying the exact types such as (Standard, Decora, other), amperage (15/20), location and method of use (this is used by good contractors to determine how many receptacles to put on a single circuit), types of lights, bulbs (R30, R40, halogens, etc.) and trims (for Hi Hats) standard, eyeballs, etc., wattage of bulbs (determines type and rating of dimmers used), there is no way of telling who is bidding what. And these are just some of the variables used for a fairly simple job!

* A good licensed contractor always uses first-class, contractor-grade materials and never uses anything else, regardless of budget. They will usually price and give you the higher grade items automatically. This is where they get in trouble when bidding with other contractors. Someone else may be using approved but inferior materials, which would enable them to come in considerably lower than the good contractor. They probably know that you'll have problems with the items installed sooner rather than later, but don't care because it falls beyond their warrantee period (if they even have one).

* A good licensed contractor will take into consideration how the receptacles are being used (such as computers, entertainment equipment, vacuum cleaner, etc.) and automatically factor in (price) dedicated lines for these items, even though current codes may allow all of the receptacles to be wired on a single circuit.

Other contractors won't, and will therefore be able to do the job cheaper. Of course, when you start tripping breakers because the new receptacles are overloading the circuit, there won't be anything to do about it, because it didn't violate any codes at the time, and more importantly, you didn't specify it.

But how could you specify it? You're not in the electrical field, and you assumed the contractor would know better and factor this in.

Well, you're right. The good contractor already factored it in, but you gave the job to the other one.

Are you starting to get the picture about the dangers of multiple bids? Very often, you don't end up with the good contractor. That's a pretty typical bidding scenario, and it is obvious why people are intimidated dealing with contractors. Make the wrong move and it can spell big trouble.

When you've finally selected a licensed contractor, ask them for a copy of their insurance policies, and make sure everything, including start and end dates is in writing.

Without this insurance policy, you (the homeowner) are 100 % liable for any accidents their workers may incur. Additionally, many contractors have only enough general liability insurance to satisfy state regulations, but nowhere near enough to pay for your house if it burns down.

Finally, a last note of caution; as with everything else in life, "you get what you pay for ".

In other words, don't let price alone be the determining factor when hiring an electrical contractor. Remember, if a plumber messes up, you'll have a flood, if an electrical contractor messes up you'll have a fire or perhaps even worse.

Good Luck.

Contact Us

We will contact you ASAP and schedule a Free In-Home Estimate which - always free of charge and without obligation.